Viewing file:  anna.h (4.72 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/*
* include/asm-v850/anna.h -- Anna V850E2 evaluation cpu chip/board
*
* Copyright (C) 2001,02,03 NEC Electronics Corporation
* Copyright (C) 2001,02,03 Miles Bader <miles@gnu.org>
*
* This file is subject to the terms and conditions of the GNU General
* Public License. See the file COPYING in the main directory of this
* archive for more details.
*
* Written by Miles Bader <miles@gnu.org>
*/
#ifndef __V850_ANNA_H__
#define __V850_ANNA_H__
#include <asm/v850e2.h> /* Based on V850E2 core. */
#define CPU_MODEL "v850e2/anna"
#define CPU_MODEL_LONG "NEC V850E2/Anna"
#define PLATFORM "anna"
#define PLATFORM_LONG "NEC/Midas lab V850E2/Anna evaluation board"
#define CPU_CLOCK_FREQ 200000000 /* 200MHz */
#define SYS_CLOCK_FREQ 33300000 /* 33.3MHz */
/* 1MB of static RAM. This memory is mirrored 64 times. */
#define SRAM_ADDR 0x04000000
#define SRAM_SIZE 0x00100000 /* 1MB */
/* 64MB of DRAM. */
#define SDRAM_ADDR 0x08000000
#define SDRAM_SIZE 0x04000000 /* 64MB */
/* For <asm/page.h> */
#define PAGE_OFFSET SRAM_ADDR
/* We use on-chip RAM, for a few miscellaneous variables that must be
accessible using a load instruction relative to R0. The Anna chip has
128K of `dLB' ram nominally located at 0xFFF00000, but it's mirrored
every 128K, so we can use the `last mirror' (except for the portion at
the top which is overridden by I/O space). In addition, the early
sample chip we're using has lots of memory errors in the dLB ram, so we
use a specially chosen location that has at least 20 bytes of contiguous
valid memory (xxxF0020 - xxxF003F). */
#define R0_RAM_ADDR 0xFFFF8020
/* Anna specific control registers. */
#define ANNA_ILBEN_ADDR 0xFFFFF7F2
#define ANNA_ILBEN (*(volatile u16 *)ANNA_ILBEN_ADDR)
/* I/O port P0-P3. */
/* Direct I/O. Bits 0-7 are pins Pn0-Pn7. */
#define ANNA_PORT_IO_ADDR(n) (0xFFFFF400 + (n) * 2)
#define ANNA_PORT_IO(n) (*(volatile u8 *)ANNA_PORT_IO_ADDR(n))
/* Port mode (for direct I/O, 0 = output, 1 = input). */
#define ANNA_PORT_PM_ADDR(n) (0xFFFFF410 + (n) * 2)
#define ANNA_PORT_PM(n) (*(volatile u8 *)ANNA_PORT_PM_ADDR(n))
/* Hardware-specific interrupt numbers (in the kernel IRQ namespace). */
#define IRQ_INTP(n) (n) /* Pnnn (pin) interrupts 0-15 */
#define IRQ_INTP_NUM 16
#define IRQ_INTOV(n) (0x10 + (n)) /* 0-2 */
#define IRQ_INTOV_NUM 2
#define IRQ_INTCCC(n) (0x12 + (n))
#define IRQ_INTCCC_NUM 4
#define IRQ_INTCMD(n) (0x16 + (n)) /* interval timer interrupts 0-5 */
#define IRQ_INTCMD_NUM 6
#define IRQ_INTDMA(n) (0x1C + (n)) /* DMA interrupts 0-3 */
#define IRQ_INTDMA_NUM 4
#define IRQ_INTDMXER 0x20
#define IRQ_INTSRE(n) (0x21 + (n)*3) /* UART 0-1 reception error */
#define IRQ_INTSRE_NUM 2
#define IRQ_INTSR(n) (0x22 + (n)*3) /* UART 0-1 reception completion */
#define IRQ_INTSR_NUM 2
#define IRQ_INTST(n) (0x23 + (n)*3) /* UART 0-1 transmission completion */
#define IRQ_INTST_NUM 2
#define NUM_CPU_IRQS 64
#ifndef __ASSEMBLY__
/* Initialize chip interrupts. */
extern void anna_init_irqs (void);
#endif
/* Anna UART details (basically the same as the V850E/MA1, but 2 channels). */
#define V850E_UART_NUM_CHANNELS 2
#define V850E_UART_BASE_FREQ (SYS_CLOCK_FREQ / 2)
#define V850E_UART_CHIP_NAME "V850E2/NA85E2A"
/* This is the UART channel that's actually connected on the board. */
#define V850E_UART_CONSOLE_CHANNEL 1
/* This is a function that gets called before configuring the UART. */
#define V850E_UART_PRE_CONFIGURE anna_uart_pre_configure
#ifndef __ASSEMBLY__
extern void anna_uart_pre_configure (unsigned chan,
unsigned cflags, unsigned baud);
#endif
/* This board supports RTS/CTS for the on-chip UART, but only for channel 1. */
/* CTS for UART channel 1 is pin P37 (bit 7 of port 3). */
#define V850E_UART_CTS(chan) ((chan) == 1 ? !(ANNA_PORT_IO(3) & 0x80) : 1)
/* RTS for UART channel 1 is pin P07 (bit 7 of port 0). */
#define V850E_UART_SET_RTS(chan, val) \
do { \
if (chan == 1) { \
unsigned old = ANNA_PORT_IO(0); \
if (val) \
ANNA_PORT_IO(0) = old & ~0x80; \
else \
ANNA_PORT_IO(0) = old | 0x80; \
} \
} while (0)
/* Timer C details. */
#define V850E_TIMER_C_BASE_ADDR 0xFFFFF600
/* Timer D details (the Anna actually has 5 of these; should change later). */
#define V850E_TIMER_D_BASE_ADDR 0xFFFFF540
#define V850E_TIMER_D_TMD_BASE_ADDR (V850E_TIMER_D_BASE_ADDR + 0x0)
#define V850E_TIMER_D_CMD_BASE_ADDR (V850E_TIMER_D_BASE_ADDR + 0x2)
#define V850E_TIMER_D_TMCD_BASE_ADDR (V850E_TIMER_D_BASE_ADDR + 0x4)
#define V850E_TIMER_D_BASE_FREQ SYS_CLOCK_FREQ
#define V850E_TIMER_D_TMCD_CS_MIN 1 /* min 2^1 divider */
/* For <asm/param.h> */
#ifndef HZ
#define HZ 100
#endif
#endif /* __V850_ANNA_H__ */
|